Natural zeolites may exhibit certain limitations in the adsorption of metal ions from aqueous solutions due to their heterogeneous mineral composition, variable content of exchangeable extra-framework cations, and the presence of impurities. In this study, natural clinoptilolite zeolite was modified using an ethanolic extract derived from lemon peel waste to evaluate the effect of this sustainable modification approach on Cu(II) adsorption from synthetic aqueous solutions. Batch adsorption experiments were conducted using 50 mL of Cu(II) solution at 300 rpm for 60 min. A one-factor-at-a-time (OFAT) approach was applied to investigate the effects of initial solution pH (2–6), initial Cu(II) concentration (10–100 mg/L), and adsorbent dosage (500-2500 mg) for both unmodified natural zeolite (UN-zeolite) and fruit-waste-extract-modified zeolite (FWEM-zeolite). All experiments were performed in triplicate. At pH 6, complete Cu(II) removal (100%) was achieved using UN-zeolite, whereas FWEM-zeolite reached a removal efficiency of 84.37%. At initial Cu(II) concentrations of 10 and 50 mg/L, complete removal was achieved using UN-zeolite, whereas FWEM-zeolite achieved removal efficiencies of 87.97% and 80.91%, respectively. Increasing the UN-zeolite dosage resulted in complete Cu(II) removal at 2000-2500 mg, while FWEM-zeolite reached its maximum removal efficiency of 91.9% at a dosage of 1000. Overall, modification with lemon peel waste extract did not improve Cu(II) removal compared with the unmodified natural zeolite under the investigated conditions. Nevertheless, FWEM-zeolite maintained high Cu(II) removal efficiency, particularly at elevated initial concentrations, demonstrating the potential of fruit-waste-derived extracts as sustainable modifying agents for natural mineral adsorbents

Water pollution by heavy metal ions poses a significant environmental problem due to their toxicity, persistence, and potential for accumulation in living organisms. Nickel requires particular attention, as it can occur at elevated concentrations in galvanic industry wastewater. Therefore, the aim of this study was to investigate the efficiency of peanut shells as a natural and readily available biosorbent for the removal of Ni(II) ions from galvanic wastewater within the context of circular economy principles. As an agricultural residue, peanut shells represent a potentially economically and environmentally acceptable alternative to conventional adsorbents. The experimental study examined the influence of key process parameters on adsorption efficiency, primarily wastewater pH, initial Ni(II) concentration, and biosorbent mass. Based on the obtained results, optimal process conditions were determined and adsorption efficiency was evaluated. The adsorption equilibrium was analysed using the Freundlich and Langmuir isotherm models. The results demonstrated that peanut shells can serve as low-cost biosorbents for the efficient removal of Ni(II) ions from galvanic wastewater. For both samples, the highest removal efficiency was achieved at pH 6 and an initial Ni(II) concentration of 1000 mg L-1. The Freundlich adsorption isotherm model showed good agreement with the experimental data, with R2>0.9 for Sample 1 and R2>0.8 for Sample 2. The comparable adsorption performance of the two samples indicates that peanut-shell residue previously used can be further valorised as a biosorbent for Ni(II) removal. The multiple use of the same biomass residue contributes to waste reduction and improved resource utilisation, supporting the potential application of peanut shells within a circular economy approach.

The rapid growth of the global population has increased the consumption of chicken eggs, leading to the generation of significant quantities of eggshell waste. The sustainable valorization of this biowaste represents an important environmental and resource management challenge. In this study, CaO was synthesized from waste chicken eggshells via calcination at 800 °C and evaluated as a green precipitating agent for the removal of toxic Pb(II) from aqueous solutions. The effects of key precipitation parameters, including initial pH, stirring speed, contact time, and CaO dosage, were systematically investigated. The results showed that the removal efficiency increased with increasing pH, mixing intensity, contact time, and CaO dosage, reaching a maximum Pb(II) removal of 90% under investigated conditions of initial pH 9, stirring speed of 500 rpm, contact time of 15 min, and CaO dosage of 500 mg. In the presence of the competing ion Fe(III), the removal efficiency further increased to 99.99%, indicating a potential synergistic effect in the precipitation process. FT-IR analysis confirmed the successful formation of CaO and revealed significant spectral changes after Pb(II) precipitation, including shifts and disappearance of characteristic absorption bands, indicating the formation of insoluble hydroxide and carbonate phases. These findings demonstrate that eggshell-derived CaO is an effective and environmentally sustainable material for Pb(II) removal from aqueous media and represents a promising approach for the valorization of eggshell waste.

Cadmium is recognized as one of the most hazardous heavy metals, ranking among the top ten in terms of toxicity. With the growing industrial reliance on cadmium for various manufacturing processes, concerns have risen within the scientific community regarding its presence in wastewater and the challenges associated with its removal. This research investigates the potential for removing Cd(II) ions from a synthetic aqueous solution by utilizing NaHCO3as a precipitating agent. The removal efficiency exceeded 99%, with the most effective conditions identified as: pH 8, a stirring speed of 300 rpm, a stirring duration of 5 minutes, and a precipitation agent of 90 mg. Additionally, removal efficiencies of 96.256% and 91.234% were achieved at cadmium concentrations of 150 mg/L and 300 mg/L, respectively. The removal of Cd(II) ions was found to be more efficient in a mixture of metals, with an efficiency above 98%, compared to when individual metals were considered in isolation.KEYWORDS:Cd(II) ions, most effective conditions, removal efficiency

Soda is a key raw material widely used in various industries, including food, pharmaceuticals, detergents, and glass production. At the "Sisecam Soda Lukavac" plant, soda is produced using the Solvay process, which relies on an aqueous solution of sodium chloride (NaCl) and calcium carbonate (CaCO₃). Due to the limited availability of global soda sources, efforts are being made to increase production capacity. However, higher production requires greater amounts of industrial water, resulting in increased consumption of fresh water from the Modrac reservoir. To reduce this consumption and minimize environmental impact, this study investigates the reuse of the waste condensate stream from the slaking drums as the aqueous solution of calcium hydroxide (lime milk) through the installation of a barometric condenser operating on the principle of direct contact between the cooling medium and steam. A barometric condenser was proposed for recovering approximately 8339.3 kg/h of steam, which would reduce water consumption by 7.58% and thermal energy losses by 29.3 %, with a payback period of less than six years. Reusing this waste condensate stream is expected to achieve significant operational, ecological, and economic improvements. KEYWORDS:soda production, waste stream, condensate, water, reuse

The paper deals with the assessment of risks related to drinkingwater quality, the analysis of physicochemical and microbiological parameters that are key to assessing human safety and health. Through a detailed analysis of these parameters, the paper investigates whether the appropriate physicochemical and microbiological parameters are within the framework defined by the regulation, and whether they may pose a threat to human health.Physicochemical parameters include aspects such as pH values, electrical conductivity, oxidizability, concentrations of various chemical compounds (such as nitrates, nitrites, ammonia, chlorides, heavy metals, etc.) and represent the degree of pollution bychemicals that may pose a threat to human health, while microbiological parameters relate to the presence of pathogenic bacteria, viruses and parasites that can cause various diseases in humans.The paper uses data from laboratory analyses of water samples monitored at 32 locations in the Tuzla Canton during two seasons. Through this assessment, the paper highlights the importance of regular monitoring of drinking water quality, as well as the implementation of adequate measures to prevent potential health hazards for users.KEYWORDS:public water fountains, physical-chemical analysis, microbiological analysis

The expansion of industrialization and household use of synthetic compounds has generated significant wastewater containing toxic heavy metals. In developing countries, this wastewater is often discharged untreated due to the high cost of advanced treatment technologies. This study used sodium hydroxide as a low-cost, readily available precipitation agent to remove selected metal ions from mono- and binary-component solutions. Unlike most studies focusing on pH and initial ion concentration, this work investigated operational parameters such as stirring speed (0–800 rpm) and time (0–30 min) while keeping pH and concentration constant. Results showed that higher stirring speeds and longer stirring times enhanced metal ion removal, with Pb(II) efficiency increasing from 86.64% at 100 rpm to 94.33% at 800 rpm. In binary mixtures, similar improvements were observed. These findings highlight that simple, low-cost operational adjustments can significantly improve metal removal efficiency, which is particularly relevant for water treatment in resource-limited settings. The two-way ANOVA without replication showed that the type of metal or mixture had a significant effect on removal efficiency, while stirring speed and time within the investigated ranges did not have a statistically significant effect. These results indicate that differences in removal efficiency are primarily due to the metals’ chemical properties rather than the operational parameters.

Zeolites are particularly suitable adsorbents due to their pronounced ion-exchange capacity, high efficiency, stability, and the ability to be regenerated and reused multiple times. Their characteristic crystalline structure enables the exchange of sodium, potassium, calcium, and magnesium ions with heavy metal cations present in solution. For the successful application of zeolites under industrial conditions, a detailed understanding of the adsorption mechanisms and kinetics is essential, as it allows for process optimization and identification of key limiting factors. Experimental approaches typically involve varying the adsorbent mass and the initial concentration of the adsorbate in order to determine the optimal conditions for achieving maximum adsorption efficiency. A moisture content of 3.95% and ash content of 91.28% indicate high thermal and structural stability of the zeolite, while the presence of Na⁺ ions (0.2435 mmol g⁻¹) in the material confirms that cation exchange is the dominant mechanism. Adsorption of heavy metals was investigated in a batch reactor at initial concentrations of 10, 50, and 100 mg/L, at a constant temperature of 298 K, with stirring at 200 rpm for 60 minutes. The amount of adsorbed ions was found to increase with rising equilibrium concentrations in the solution. Metal ion concentrations were determined using atomic absorption spectrophotometry. The highest adsorption was observed for Cu(II) ions within 5 minutes, while Cr(III) and Ni(II) ions reached their maximum adsorption within 20 minutes. The experimental data fit best to the Langmuir isotherm model, and the adsorption efficiency followed the order: Cu(II) > Cr(III) > Ni(II).

Physical chemical milk is an emulsion of milk fat in an aqueous solution of proteins, milk sugar and mineral salts. The high molar conductivity of goat milk samples compared to cow's milk indicates a high content of mineral substances. That goat milk is rich in total proteins is also indicated by the protein content in the samples, which are higher than the cow's milk samples. However, higher fat content was recorded in cow's milk samples, which also results in higher surface tension of cow's milk. The freezing point and refractive index of goat milk are higher compared to literature data and cow milk samples. The acidity of goat's milk comes from the acidic properties of casein, citrate, phosphate, etc. it is lower than cow's milk and is in accordance with literature data. The viscosity of pasteurized goat's milk at all temperatures is also higher than that of cow's milk.

In accordance with consumer requirements, the water must be adequately purified, and the corresponding parameters within the defined values. Various methods are used for this purpose, of which the ion exchange method can be highlighted as the simplest, most efficient and economically profitable. Ion exchange is a reversible process of ion exchange between a solid phase and an electrolyte solution. The ion exchanger is a macromolecular insoluble material that has chemically bound electrified groups and mobile, oppositely charged ions that compensate for this electrification. Ion exchangers are usually used in the form of compact or granular beds that fill the column through which the solution with the ions to be exchanged flows.They usually contain phenolic, carboxylic, sulfonic amino and other groups, which is why the treatment also results in decarbonization, softening, demineralization and denitrification of water. As the assessment of water quality is based on the most significant physico-chemical parameters, the aim of the work is the analysis of drinking water before and after treatment with an ion exchanger.For this purpose, organoleptic parameters such as smell, taste and color were first analyzed. After that, physico-chemical parameters were analyzed: pH values, electrical conductivity, m-alkalinity, p-alkalinity, water hardness, organic matter content, chloride content, iron and manganese content. An ion exchanger based on resin was used, which after use was regenerated by washing with NaClsolution.The analysis of the water sample, before and after the ion exchange treatment, showed that the treatment process was effective and that the decarbonization and softening of the water was carried out, whereby the water was categorized as soft water (water <9⁰dH).The analyzed water is tasteless, odorless and colorless before and after treatment. The results of the analysis showed that all the values of the analyzedphysico-chemical parametersare in accordance with the Rulebook on the Healthiness of Drinking Water(Official Gazetteof Federation of Bosnia and Herzegovina No.40/10) arebelow the maximum allowed values. KEYWORDS:water, ion exchange, physical-chemical parameters; water treatment

Waste water in the galvanic process contains high concentrations of heavy metals that pose a direct danger to humans and the environment. Conventional methods for their removal are quite expensive and generate a large amount of waste. The development of new and improvement of existing methods for the removal of heavy metals from galvanic wastewater are the subject of many studies. Compared to other purification methods, the adsorption is becoming an increasingly popular method of wastewater purification, especially if the adsorbent is cheap, easily available and does not require any other treatment before use. Therefore, the aim of the work was to investigate the possibility of using natural bentonite for the removal of heavy metal ions from multi-component water systems of the galvanic industry. For this purpose, the physico-chemical characterization of natural bentonite was performed, and then the influence of pH value, time and temperature on the adsorption efficiency was examined. The results of adsorption showed that natural bentonite can be used as an adsorbent for the removal of heavy metal ions from waste galvanic waters, and that at pH 5 it achieves the maximum removal efficiency for Cu(II):Cr(III):Ni(II) ions in the percentage ratio 100 : 99.990 : 99.998. The results showed that the highest removal efficiency for Cu (II) ions was achieved in the first 10 minutes, and 20 minutes for Cr (III) and Ni (II) ions. The maximum efficiency of Cu (II) removal was achieved at all temperatures, while for Cr (III) 99.99% and Ni (II) 100% maximum efficiency was achieved at 35°C, which indicates that the adsorption process is endothermic. The experimental results of the adsorption of Cu (II) metal ions are in good agreement with the Langmuir and Freundlich theoretical models, while for Cr (III) and Ni (II) ions they are in better agreement with the Langmuir adsorption model.

Industrial production generates enormous amounts of wastewaters with a high content of organic and inorganic substances, which must be treated before discharging into a natural recipient to such a quality that it will not have a negative impact on the aquatic environment. This paper shows the possibility of applying a multi-stage process with Fenton reagents in combination with bentonite as an adsorbent in the treatment of ammonia-phenolic wastewater. The role of bentonite clay in this study was dye removal. The investigation was carried out under laboratory conditions, and the efficiency of the process was determined on the following parameters of COD, ammonia, phenol and thiocyanate. Also, the influence of the pH value, the concentration of oxidant hydrogen peroxide and catalyst iron sulphate heptahydrate was examined. The optimal values obtained for the pH, concentration of hydrogen peroxide and the catalyst iron sulphate heptahydrate was: 3; 30% and 23 g/l, where the efficiency of removal of the COD, ammonia, phenol and thiocyanate was: 96.42 %; 85.17 %; 100 % i 99.13 %.

Medicinal plants have become an increasing subject of interest worldwide due to the large amount of biologically active substances that have potential beneficial health properties. One of the more interesting popular medicinal plants is hawthorn (Crataegusspp.), a deciduous branched shrub that is increasingly used for health purposes. Various parts of this plant, including berries, flowers and leaves, are rich in nutrients and beneficial bioactive compounds that are effective in the treatment of numerous diseases. Honey is a natural sweetener produced by bees from plant secretions. Known for its nutritional and medicinal values, it gives strength to the body, which is why it is indispensable in the human diet. The combination of these two ingredients represents a significant source of vitamins and minerals in daily use, but also for use in various pharmaceutical and medical purpose. Taking into account all of the above, the aim of the work is to test samples of the mixture of honey and hawthorn in different proportions and determine the physical and chemical characteristics: pH value, electrical conductivity, refractive index, viscosity, water activity, HMF, DPPH. Based on the analysis, appropriate conclusions will be drawn and more information will be obtained about their quality and possible use as a food supplement. On the basis of the conducted analyses, it can be concluded that the parameter values are within the permitted limits defined by the Rulebook (Official Gazette Bosnia and Herzegovina No. 37/09). The analysis of the mentioned parameters showed that the chemical composition of the sample plays a major role in the value of the measurement results, and that Sample III has the best antioxidant properties. KEYWORDS:physicochemical characteristics; honey; hawthorn (Crataegus spp.);mixture; food suplement

Adsorption with bentonite offers an efficient, cost-effective and environmentally friendly method for the treatment of ammonia-phenolic wastewater. Therefore, raw bentonite and organoactivated bentonite with hexadecyl trimethyl ammonium bromide (CTAB) were used as adsorbents for the removal of total ammonia, total phenols and total cyanides from untreated ammonia-phenolic wastewater. Better percent removal of total ammonia (34.64%), total phenols (42.50%) from ammonia-phenolic wastewater was achieved with CTAB activated bentonite compared to raw bentonite. Raw bentonite is recommended for the removal of cyanide ions from ammonia-phenolic wastewater over CTAB activated bentonite. Although both adsorbents give a similar percentage of removal, raw bentonite is considered a cheaper option compared to activated due to additional cost and time, so it would be the choice for removing these ions.

pH represents the concentration of free H+ in pine needles extracts (PNE) and is therefore an important initial parameter in quality control. Electrical conductivity and pH of samples of fresh and stored for 20 days of PNE with black cumin oil and olive oil had values of 0.00 due to the encapsulation of water molecules, pH and electrical conduction was not possible. The pH of the other samples was in a weakly acidic environment because the pH of natural pine needles is 3.8. Electrical conductivity values in all samples except pine needle extract and honey increased during storage. By monitoring the parameters of pH and electrical conductivity in the quality control of PNE, it gives us a significant insight into the physical state of the phases and the way of storage.